?
?
Hardware Reference Manual for i.MX53 Quick Start
?
?
?
5.15. Debug   UART   Serial   Port  
?
?
The ? i.MX53 ? Applications ? Processor ? has ? 5 ? independent ? UART ? Ports ? (UART1 ? – ? UART5). ? The ? Processor ? will ?
boot ? by ? default ? using ? UART1 ? to ? output ? serial ? debugging ? information, ? specifically ? on ? pins ? CSI0_DAT10 ?
(pin ? R5) ? and ? CSI0_DAT11 ? (pinT2). ? These ? two ? pins ? are ? output ? from ? the ? NVCC_CSI ? module, ? which ? is ? pulled ?
up ? to ? 1.8V ? on ? the ? Quick ? Start ? board. ? In ? order ? to ? convert ? the ? UART ? Transmit ? and ? Receive ? signal ? to ? a ? 3.2V ?
logic ? signal, ? two ? single ‐ direction ? level ? shifters ? (U25, ? U26) ? are ? used. ? The ? level ? shifted ? signals ? are ? sent ? to ? a ?
low ? cost, ? RS232 ? transceiver, ? which ? reformats ? the ? signals ? to ? the ? correct ? voltages ? and ? drives ? the ? signals. ?
The ? resulting ? cable ? ready ? signals ? are ? then ? connected ? to ? the ? RS232 ? Debug ? connector. ? No ? RTS ? or ? CTS ?
signals ? are ? sent ? from ? the ? Processor ? to ? the ? Debug ? connector ? since ? these ? signals ? are ? commonly ? ignored ? by ?
most ? applications. ? The ? required ? terminal ? settings ? to ? receive ? debug ? information ? during ? the ? boot ? cycle ? are ?
shown ? in ? Table ? 13 : ?
?
?
?
?
?
?
?
?
Data ? Rate ?
Data ? bits ?
Parity ?
Stop ? bits ?
Flow ? Control ?
115,200 ? Baud ?
8 ?
None ?
1 ?
None ?
?
????????? Table ? 13 . ? Terminal ? Setting ? Parameters ?
?
?
?
If ? the ? developer ? wishes ? to ? repurpose ? the ? Debug ? UART ? connector ? in ? software ? into ? an ? Applications ?
connector, ? the ? Quick ? Start ? board ? can ? support ? this ? using ? a ? Null ? Modem ? Adapter. ? The ? adapters ? are ? readily ?
available ? from ? most ? cable ? and ? electronics ? stores ? at ? a ? small ? cost. ?
?
See ? the ? section ? on ? the ? Expansion ? Port ? to ? find ? how ? to ? access ? some ? of ? the ? other ? UART ? channels ? on ? the ?
Quick ? Start ? board. ?
?
?
? ?
Freescale Semiconductor
Hardware User Guide for i.MX53 Quick Start Board,
Preliminary Rev 0.91
61
PUBI – Public Use Business Information ?
相关PDF资料
MCM69C432TQ20 IC CAM 1MB 50MHZ 100LQFP
MCP1401T-E/OT IC MOSFET DRVR INV 500MA SOT23-5
MCP1403T-E/MF IC MOSFET DRIVER 4.5A DUAL 8DFN
MCP1406-E/SN IC MOSFET DVR 6A 8SOIC
MCP14628T-E/MF IC MOSFET DVR 2A SYNC BUCK 8-DFN
MCP14700T-E/MF IC MOSFET DRIVER HIGH/LOW 8DFN
MCP14E3T-E/MF IC MOSFET DVR 4.0A DUAL 8DFN
MCP14E6T-E/MF IC MOSFET DRIVER 2A 8DFN-S
相关代理商/技术参数
MCIMX53-START-R 制造商:Freescale Semiconductor 功能描述:DEV KIT I.MX53 1GHZ ARM CORTEX A8 制造商:Freescale Semiconductor 功能描述:I.MX53, WITH PMIC, QUICK START BOARD 制造商:Freescale Semiconductor 功能描述:I.MX53, WITH PMIC, QUICK START BOARD; Silicon Manufacturer:Freescale; Core Architecture:ARM; Core Sub-Architecture:Cortex-A8; Silicon Core Number:i.MX53; Silicon Family Name:i.MX53; Kit Contents:Processor, PMIC, microSD, Power ;RoHS Compliant: No
MCIMX53XA 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:i.MX53xA Automotive and Infotainment Applications Processors
MCIMX53XD 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:i.MX53xD Applications Processors for Consumer Products
MCIMX6 SOLO 制造商:RIOTBOARD 功能描述:I.MX6 GC2000 CORTEX A9 DEV BOARD 制造商:RIOTBOARD 功能描述:RIOT BOARD DEVELOPMENT PLATFORM
MCIMX6 SOLO 制造商:RIOTBOARD 功能描述:Freescale i.MX6Solo community board
MCIMX6D4AVT08AC 功能描述:处理器 - 专门应用 i.MX6D AUTO RoHS:否 制造商:Freescale Semiconductor 类型:Multimedia Applications 核心:ARM Cortex A9 处理器系列:i.MX6 数据总线宽度:32 bit 最大时钟频率:1 GHz 指令/数据缓存: 数据 RAM 大小:128 KB 数据 ROM 大小: 工作电源电压: 最大工作温度:+ 95 C 安装风格:SMD/SMT 封装 / 箱体:MAPBGA-432
MCIMX6D4AVT08ACR 功能描述:处理器 - 专门应用 i.MX6D AUTO RoHS:否 制造商:Freescale Semiconductor 类型:Multimedia Applications 核心:ARM Cortex A9 处理器系列:i.MX6 数据总线宽度:32 bit 最大时钟频率:1 GHz 指令/数据缓存: 数据 RAM 大小:128 KB 数据 ROM 大小: 工作电源电压: 最大工作温度:+ 95 C 安装风格:SMD/SMT 封装 / 箱体:MAPBGA-432
MCIMX6D4AVT08ACR2 制造商:Freescale Semiconductor 功能描述:MCIMX6D4AVT08ACR2 - Tape and Reel